Jet-Loader
Two versions and a great variety of accessories allow optimum adaption of every installation to silos for bulk goods, to charging points,
and to all kinds of processing sequences.

Areas of application
Wherever loose, powdery or grainy bulk goods are to be loaded rapidly and ecologically safe, the Jet Loaders will be actively involved. Whether for cement, lime, plaster, ready-to-use roughcast, REA products, or other pneumatic bulk goods - the Jet Loaders will work reliably and free of traoubles. Careful choice of materials and solid workmanship are the basis for good performance. Certain constructive details safeguard additional advantages.

Advantages
· High operational security: By locating two pull lines outside of the material flow, the wear of these cables is practically reduced to zero, thus eliminating an otherwise frequent source of troubles and accidents.
· Gentle on the outer bellows The inner buckets are individually suspended on sturdy straps in order to limit the stroke range of the loader. The outer bellows can therefore not be damaged by overload.
· Protected drive: All drive and control devices are concentrated within the loader head, where they are well protected and yet easily accessible.
· Compact design: Even if space is limited, the loader can be used without problems, since tehre are no pull cables and outside winches getting in the way.
· Simplified installation: Just screw it on and hook up the power: Your Jet Loader is ready to operate.
· Exactly guided material flow
· Continuously variable speed: Rapid lowering and gentle setting down, as well as soft lifting-off and rapid raising result in economy through shortened charging times.
· Tight seat: The filling spout is coated with elastomer to insure the gapless connection to the filling dome.
· Easy to service: Pull cables, rods, and the drive machanisms are easily accessible.
· Adaptable: The material and the consistency of the buckets can be exactly adapted to the characzeristics of materials to be handled.
· A large range of accessories: Every type of silo, every charging point can be equipped with the Jet Charger. The system is variable and can be adapted functionally and economically to any requirement by an ample range of accessories.
· Compact drive motor with integrated end switches, and with emergency control for cases of trouble.

Two different Types of Loader:

Type QUADRO with square buckets
 · with shutter cone
· for powdery goods
· standard size 220 x 220 mm
· buckets can be mad of:
    - sheet steel
    - high wear-resistant steel
    - special steel
· Exclusively for loading silo vehicles and containers


 Type RONDO with round buckets
· with shutter cone
· for powdery goods
· all extra sizes
· buckets can be made of:
    - cast steel
    - sheet steel
    - steel 50
    - special steel
    - plastic material
· for loading hopper vehicles and open transport vehicles
· mechanical level compensation

The Filling-Level-Monitor
The filling level monitors are essential elements for the automation of the material flow. Depending on the physical properties of the material, different types of filling level monitors will be required.

· rotary-wing monitor for powdery and granular bulk goods up to (y) 0.5
· vibrating probe for powdery bulk goods, even for very light materials
· capacitive probe for high-density powdery and granular bulk goods that can be measured capacitively
· ultrasonic probe for granular bulk goods, and when dust hoods are used
· pneumatic filling-level monitor for powdery bulk goods with more than (y) 0.5

 Compact Design
The drive mechanisms of the Jet Loaders are integrated in the loader head, and are readily accessible.
This is highly advantageous for installing.

Integrated Filter
As an alternative to the conventional dedusting filters, the Jet-Loader-Filters are supplied with a pneumatic cleaning device. It is directly mounted on the loader head, thus using the shortest way to clean the dust-air mixture. The remaining dust is led directly into the hopper vehicle.
The variable mounting system requires no additional mounting height.

Pneumatic cleaning
The rubber-coated filling spout, the movably suspended inner buckets, and the flexible bellows with their otherwise so useful elasticity, will however become problemativ when cleaning with a mechanical vibrator. For this reason we designed an advantageous pneumatic cleaning system, by which the inner buckets and the outer bellows are alternatedly hit by compressed-air pulses and thus cleaned.
The smae holds true for the exhaust space within the spout.

Back to survey 'jet-loader types / loaders'