Air
conveyor trough
for the horizontal
transportation of dusty material
Application
The air conveyor trough is used for horizontal transportation of dusty
material. (Semonimal) gravally products cannot be transported. Depending
on the material type and conveying capacity, the air conveyor trough
nust be installed with an angle of inclination betwenn 5° - 7°.
Material
Body: St 1203, AIMg 3 oder Mat. 4541 und 4571
Aeration plate: Synthetic substances or Sinter metall (Pewter bronze or
VA)
Sealing: Rubber
Construction
The air conveyor trough consits of an upper- and lower box, which is
separated by the porous aeration plate. The dispersion air is blown into
the lower box, while the material to be conveyed is being moved.
Both boxes are firmly screwed together and sealed against each other.
The conveyor troughs are manufactured in pieces not longer than 2500 mm
max. and can be screwed together to any length.
Appropriate in- and output elements are supplied. An air ventilator is
normally used as air source, which is firmly mounted onto the conveyor
trough. Ech conveyor trough section has a hand inspection part as shown
in schematic.
Electrical equipment
As operating drive for the ventilator a special motor is used.
Protection and voltage according to request.
Operation data:
Air volume/m2: dependent on trough inclination and porous
material
Air pressure: dependent on porous material
Special features
Using the air conveyor trough, a gentle conveying of powdery material is
guaranteed. Only limited obsolescence occurs as against mechanical
conveying belts like screw conveyors as rotating parts are not used. The
aeration plate has a long lifetime and can often be regenerated. The
hand inspection part allows a controlled operation and maintenance e.g.
to clean the trough without dismanting.
Unlimited input- and output end elements can be installed. Conveying
length does not matter, as long as enough height is available.
Measurement table
Construction ist subject to change.
Dimension Drawing
Dimension Table
| Size |
Capacity |
Length |
Sinter
metall |
Aeration
plate synthetic substances |
W.* |
| |
m3/h |
L |
A |
B |
C |
D |
E |
S |
C |
D |
E |
S |
F |
G |
| 10 |
10 |
500-2500 |
183 |
164 |
98 |
66 |
48 |
3 |
98 |
66 |
46 |
5 |
170 |
60 |
| 25 |
25 |
500-2500 |
223 |
214 |
148 |
101 |
53 |
3 |
148 |
101 |
51 |
5 |
150 |
90 |
| 50 |
50 |
500-2500 |
331 |
264 |
198 |
182 |
80 |
3 |
198 |
182 |
78 |
5 |
120 |
120 |
| 80 |
80 |
500-2500 |
331 |
314 |
248 |
182 |
80 |
3 |
248 |
182 |
78 |
5 |
120 |
120 |
| 120 |
120 |
500-2500 |
441 |
374 |
298 |
256 |
106 |
3 |
298 |
256 |
104 |
5 |
120 |
120 |
| 200 |
200 |
500-2500 |
500 |
424 |
348 |
321 |
100 |
3 |
348 |
321 |
98 |
5 |
120 |
120 |
W.*: weight kg/m
Back
to survey 'conveyor belts / pneumatic conveying'
|
